Qnap supersync itunes
If the blue power light goes out after several seconds, the server is booting up fully, there is NOT a problem with the server, but there is a problem with your network - described below.
#Qnap supersync itunes code
If the blue power light goes out immediately then there may be a fault with the server - quote fault code F02. To test this, click the power button on the front plate of the server. Opening The VortexBox GUI If you have allowed 3 minutes for the server to boot up, but cannot browse to the VortexBox GUI (by entering antipodes1 or antipodes1.local in the address bar of a browser), it is possible that your server is not booting up fully.
![qnap supersync itunes qnap supersync itunes](http://mlb-s1-p.mlstatic.com/servidor-nas-qnap-ts-451-8tb-4x-seagate-nas-hdd-2tb-itunes-556201-MLB20286786127_042015-F.jpg)
Contact your dealer or Antipodes Audio quoting fault code F01. when you click the power button on the frontplate of the server the blue light does not illuminate - then your server is faulty. If fully powered down for a period, a burned in server may take around 40 hours to return to its optimum performance. A new server will take about a week to burn in and perform close to its best, and will improve for some weeks, so we recommend you connect and leave a new server running for about a month to complete burn in. You may even prefer to leave the server booted up permanently for the best sound. If possible leave the power on at the rear of the server permanently, as this keeps the key capacitors powered and so ensures the server is always ready to perform at its optimum audio quality.
![qnap supersync itunes qnap supersync itunes](https://i0.wp.com/www.thestreamingblog.com/wp-content/uploads/2016/08/QNAP-Preview.png)
![qnap supersync itunes qnap supersync itunes](https://img.netzwelt.de/dw1600_dh900_sw0_sh0_sx0_sy0_sr16x9_nu0/picture/original/2016/11/qnap-qnap-251-plus-205040.png)
For servers with an IEC inlet, turn the switch from ‘0’ to ‘1’. The power setting can be changed, and the fuses checked, by using a thin flat screwdriver to flip the IEC receptacle open to re-fit the red fuse holder so that the correct voltage shows. For servers with internal power supplies, check that the red window on the IEC inlet shows the correct power setting. Turning The Server On/Off For servers powered by an external SMPS power supply, check the power light is lit on the power supply brick, and that the power connection to the server is correctly made. However a wired connection is recommended: - for the reliable operation of the server, - if you are playing from a NAS, - if you are playing internet streaming services, or - if you are using the music server as a DLNA server or DLNA renderer.
![qnap supersync itunes qnap supersync itunes](https://s11234.pcdn.co/wp-content/uploads/2015/04/SuperSync_1.jpg)
This does not affect sound quality when playing from internal storage through the USB outputs.
#Qnap supersync itunes install
MORE INFORMATION Installation If it is not practical to install a wired Ethernet connection from your router to your stereo, you can use bridged wireless access points or Ethernet over Power plugs. Installation Opening The VortexBox GUI Configuring Players Playing Music Ripping Disks Accessing Music Files To Copy or Delete Them Playing From A USB Disk Playing From Another Antipodes Server Playing From A NAS Synchronising With iTunes Editing Music Tags & Cover Artį01 Server Not Powering Up F02 Server Not Booting Fully F03 Server Not Connecting to Network F04 USB Audio Output Problem F05 Server Playing But No Sound F06 CD Auto-Ripper Problem It should be read in conjunction with the Quick Guide, which can be found at. REFERENCE GUIDE Introduction This Reference Guide provides additional information to add explanation to the Quick Guide. ALL RIGHTS RESERVED ANTIPODES AUDIO LIMITED